A specialist reference comparing the three insulation cores used in cam-lock cold-room panels — sztywny poliuretan (PUR), polyisocyanurate (PIR)i mineral wool — on thermal performance, capital cost, and payback. Written for refrigeration engineers, facility managers, specifiers, and food-safety officers evaluating the lifetime cost of an insulated envelope, not just its purchase price.

Krótka odpowiedź: Over a 10–20 year service life, the insulation core is decided by energy cost, not panel price. PUR and PIR are close on thermal conductivity (λ ≈ 0.022–0.025 W/m·K aged); mineral wool is roughly 1.6–1.8× worse (λ ≈ 0.038–0.040 W/m·K) and needs a thicker, heavier panel for the same U-value, but it is non-combustible (Euroclass A). For most chill and freezer rooms a closed-cell foam wins on running cost; mineral wool wins only where fire rating is the governing requirement. The single biggest TCO lever is not the foam chemistry — it is panel thickness, joint sealing, and install quality. Frostbox (Algor) panels use a PUR core in 80/100 mm (chłodzenie) i 100/120 mm (freezer); to size yours, use the Kalkulator doboru komory.

Why insulation drives total cost of ownership

The purchase price of cold-room panels is a one-time number. The energy bill to hold temperature is a number you pay every hour for the next 10–20 years. Across a typical cold-room service life, cumulative energy cost usually dwarfs the capital cost of the panels themselves, so the correct way to compare insulation options is total cost of ownership (TCO) — capital plus lifetime energy plus maintenance — not the headline panel quote.

Insulation governs the energy term directly. The better the core resists heat flow, the smaller the continuous cooling load the refrigeration plant must remove, the less the compressor runs, and the lower the electricity bill. A higher-performing core also holds temperature more steadily through door openings and defrost cycles, which reduces compressor wear and protects product quality. Those second-order savings are real but harder to quantify; the energy term is the one that dominates the payback maths below.

The three core materials at a glance

All three cores are used in modular cam-lock panels and all fall under the harmonised European product standard EN 14509 (self-supporting metal-faced insulating sandwich panels). They differ sharply in thermal efficiency, weight, fire behaviour, and how their performance ages.

Standardowa oferta Frostbox: Frostbox panels (manufactured by MTH, "Algor" line) use a sztywny poliuretan (PUR) core. The catalogue is 80 mm i 100 mm do chłodni i 100 / 120 mm for freezing rooms. The comparison above is generic industry reference — PIR and mineral-wool figures describe the wider market, not the Frostbox product. A formal fire-classification / Declaration of Performance (DoP) for the PUR core is available on request via [email protected].

A note on λ and "R-value per inch"

North-American datasheets quote insulation as R-value per inch; European panels are specified by thermal conductivity λ (W/m·K) and the panel's overall U-value (W/m²·K). They describe the same physics. To convert a per-25 mm SI thermal resistance into λ, divide thickness (m) by resistance (m²·K/W). The headline takeaway for an EU specifier: PUR and PIR sit around λ ≈ 0.022–0.025 W/m·K, mineral wool around λ ≈ 0.040 W/m·K — so a mineral-wool panel must be markedly thicker to match a foam panel's U-value. (The often-quoted "λ = 0.022 W/m·K" is a typical fresh PUR/PIR value; real, aged panel performance is a little higher and is what the U-value on a DoP should reflect.)

Thermal performance and what it costs you

Why a small λ difference matters across a whole room

A cold room is a large surface area held at a fixed temperature difference from ambient, around the clock. Conductive heat gain through the envelope is roughly proportional to the U-value, so even a modest improvement in core conductivity multiplies across hundreds of square metres of wall, ceiling, and floor and across every hour of operation. This is why insulation choice shows up on the electricity bill rather than the thermostat.

Two design levers move the U-value:

1. Core conductivity (λ) — the material choice. PUR ≈ PIR, both clearly better than mineral wool.
2. Core thickness — the cheaper and usually larger lever. Going one thickness step up (e.g. 80 → 100 mm) cuts conductive gain more than switching foam chemistry at constant thickness.

For most projects, getting the thickness right matters more than agonising over PUR vs PIR. A correctly sized 100 mm PUR freezer panel will outperform an under-thick PIR one every time.

Where mineral wool earns its place

Mineral wool is thermally worse and heavier, but it is non-combustible (Euroclass A1/A2 reaction-to-fire) and acoustically absorbent. It is the right core when:

• Fire rating governs the specification — e.g. compartment walls, firebreak panels, or insurer/jurisdiction requirements demanding an A-class core regardless of thermal penalty.
• Acoustic performance matters (plant rooms, dividing walls).
• A facility's risk assessment ranks combustibility above energy efficiency.

PIR is the usual middle path: foam-grade thermal performance with markedly better fire behaviour than PUR (it chars and resists flame spread rather than burning freely), at a small cost premium. Where a project needs both low U-value and an improved fire profile, PIR — not mineral wool — is often the better-value answer.

Operating-cost mechanisms

Beyond steady-state conductive gain, insulation quality affects three operating-cost streams:

• Energy consumption. The dominant term. Lower U-value → lower continuous refrigeration load → fewer compressor run-hours → lower kWh. The effect compounds in hot/humid climates and in continuously run freezers.
• Temperature stability. A high-performing, well-sealed envelope resists swings during door traffic and defrost. Steadier temperatures reduce compressor cycling (which wears equipment) and protect product, cutting spoilage and shrink. See Codzienne funkcjonowanie i Efektywność energetyczna.
• Maintenance and longevity. Closed-cell foams and mineral wool are all low-maintenance provided the metal facings and joint seals stay intact. The real-world cost driver is not the core chemistry but breached panels and leaking joints: a forklift dent, an unsealed penetration, or a failing gasket lets in warm, moist air that condenses, degrades the core, and quietly raises the energy bill. Cam-lock construction makes a damaged panel individually replaceable — see Częste błędy instalacyjne.

Thermal drift, briefly. Foam cores (PUR/PIR) age: the low-conductivity blowing-gas in the cells slowly diffuses out and is replaced by air, so λ rises a little over years — the "aged" value in the table is what matters for TCO. Mineral wool relies on trapped air and does not drift. For both foams, the metal facings act as a vapour-and-gas barrier that slows this ageing; intact facings are therefore a TCO factor, not just a hygiene one.

Payback: a worked, illustrative example

Poniższe dane przedstawiają ilustracyjny — chosen to show the method, not to quote a guaranteed result. Always run the calculation with your own room geometry, local electricity tariff, and a supplier U-value (from the panel's DoP).

Scenariusz. Two otherwise-identical freezer rooms, ≈ 100 m² of envelope surface, held at −18 °C in a climate averaging +25 °C ambient, running 24/7 for 10 years. Both panels are 100 mm thick. One uses a PUR core, the other a marginally better PIR core.

At an illustrative EU electricity price of €0.20/kWh, the ≈ 3,000 kWh/yr saving is about €600/yr, or roughly €6,000 over 10 years — which can offset the PIR panel premium and then continue as net saving, before counting reduced spoilage and lower compressor wear. (At €0.30/kWh the annual saving rises to ≈ €900; the payback is tariff-driven, which is exactly why it must be computed locally.)

How to read this: the foam-vs-foam gap is real but modest. The far larger numbers come from (a) choosing adequate thickness, (b) sealing the joints, and (c) sizing the refrigeration correctly — get those wrong and no core chemistry saves you. Conversely, the mineral-wool-vs-foam gap is large (≈ 1.6–1.8× the conductivity), so a fire-led decision to use mineral wool carries a genuine, ongoing energy premium that should be made with eyes open.

Method note. Simple payback ignores the time value of money and tariff inflation. For a capital case, also compute net present value (NPV) of the energy stream and an internal return on investment (ROI); for cold-room TCO methodology and EU/PL incentive framing, see the economics deep-dives in Powiązane artykuły. Use EU/Polish energy-efficiency incentive schemes where applicable — not US ENERGY STAR / LEED figures, which do not apply here.

Choosing a core: a decision framework

Zasady ogólne:

• Size the thickness first, choose the chemistry second. A thickness step (80→100, 100→120 mm) usually buys more energy saving than a foam swap at constant thickness.
• Let fire code, not marketing, force mineral wool. If an A-class core isn't required, a foam core almost always wins on TCO.
• Compute payback with a local tariff and a DoP U-value. "Typical λ" values are starting points, not guarantees.
• Protect the envelope you bought. Sealing, vapour barriers, and damage-free facings preserve the rated performance for the asset's whole life.

For deeper background on the underlying physics, see Nauka o izolacji i Obliczanie obciążenia cieplnego; for the panel build itself, see Specyfikacja paneli. When you are ready to specify a room, the Kalkulator doboru komory sizes panels to your dimensions and ambient, and you can Poproś o wycenę.

Powiązane artykuły

• Specyfikacja paneli
• Nauka o izolacji
• Cold-room durability factors
• Insulation & environmental impact
• Cold-room economics: operating costs
• Cold-room economics: ROI methods

Źródła i literatura uzupełniająca

• EN 14509 — Self-supporting double skin metal faced insulating sandwich panels — Factory made products — Specifications. (European Committee for Standardization, CEN). The governing harmonised product standard for PUR, PIR and mineral-wool faced panels and their declared U-values.
• EN 13165 (rigid polyurethane/PIR foam) and EN 13162 (mineral wool) — factory-made thermal insulation product standards defining declared thermal conductivity (λ) and ageing procedures.
• EN 13501-1 — Fire classification of construction products (Euroclasses A1–F). Basis for the non-combustible (A1/A2) rating of mineral-wool cores vs. the reaction-to-fire class of foam cores.
• ISO 8301 / ISO 8302 — heat-flow-meter and guarded-hot-plate methods for measuring thermal conductivity (λ) of insulation.
• ASHRAE Handbook — Refrigeration, "Insulation Systems for Refrigerant Piping" and cold-storage envelope chapters — engineering reference on U-value, heat gain, and lifecycle energy. ashrae.org
• PU Europe (European polyurethane insulation industry association) — declared λ, thermal-drift / ageing, and DoP guidance for PUR/PIR panels. pu-europe.eu
• EURIMA (European Mineral Wool Manufacturers Association) — mineral-wool λ, fire (Euroclass A) and acoustic data. eurima.org
• "PIR vs PUR vs Rockwool sandwich panels: differences, performance & best uses" — manufacturer comparison of core λ, thickness-for-U-value, and fire behaviour. sqpanel.com
• "Differences between PUR/PIR and rock wool sandwich panels" — Synthesia Technology — core-material comparison for cold-store panels. blog.synthesia.com
• Izopanel — Sandwich panels technical catalogue (declared λ and U-value tables for PUR/PIR/mineral-wool cores). izopanel.org

Specifications for the Frostbox / MTH Algor PUR panel system — including U-values, fire classification, and load ratings — are available on request: [email protected].